ADURO 7 Manuel d'utilisateur Page 7

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 8
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 6
- 7 -
When stoking
Each time fresh wood is put in the stove, a precise amount of primary air will be allowed in for the first few
minutes. What’s more important is that the primary air is not allowed in for too long. This is to ensure
optimum combustion. The Aduro-tronic control will ensure intake of primary air at the right tempo. The
automatic is activated by pulling the primary damper out each time fresh wood is put in the stove. The
automatic closes then the primary air gradually.
Regulation of the Aduro-tronic control
The control is pre-set to allow primary air intake for the first 5 minutes. This setting has been used during
testing at the Danish Technological Institute using ‘standard’ sized logs and with optimum moisture content
of 17-20%. Standard size logs are approx. 30 cm long and 10 x 10 cm in thickness. A standard chimney was
also used for testing. In practice, such circumstances can differ, which is why the Aduro-tronic control can be
adjusted to your circumstances. If you want a slower intake of primary air: (e.g. for a slower flue draught,
larger sized wood or for longer intervals between stoking) Adjust the screw on the front of the control level
using a small screwdriver to slow closure rate. If the screw is turned to the right closing time is increased and
if turned to the left closing time is reduced.
3.9 Ventilation/fresh air supply
In order for the wood burning stove to function at optimum efficiency, air is needed for the combustion
process. There must be sufficient fresh air coming into the room containing the wood burning stove. In very
well-insulated houses, or houses with powerful cooker hoods and/or air conditioning systems, a vacuum can
be created around the wood burning stove, leading to smoke leakage and poor combustion. In these
circumstances, it might be necessary to open a window to provide air for combustion and to equalize the
vacuum. Alternatively, you could fit an air vent in the room containing the wood burning stove.
4.0 The chimney
Data for chimney calculation:
Wood
Flue temperature at [20 °C]
330
Chimney draught at testing power
[mbar]/[Pa]
0.12/12
Flue gas mass flow [g/s] 6.4
The optimum combustion is achieved at a constant chimney draught of 0.10 to 0.14 mbar measured in the
flue pipe above the stove. There are many factors that affect the chimney draught, including the outside
temperature, wind strength and surrounding buildings. If it is impossible to establish a sufficiently natural
chimney draught, the chimney can be fitted with a smoke extractor. If the chimney draught is too strong, a
damper can be fitted to regulate the chimney draught. Contact your local chimney sweep for more advice.
4.1 Inadequate draught in the chimney
If the chimney is too short, leaks or is inadequately insulated, there may be problems with the chimney
draught (let the chimney sweep assess this). The draught should be approx. 0.10–0.14 mbar in order to
provide satisfactory combustion and prevent smoke leakage.
If the chimney sweep judges the draught to be satisfactory, but you still have problems lighting a fire, try
extending the fire lighting phase/using more thin pieces of kindling, so that the chimney gets thoroughly
warm. The chimney will not draw at optimum effect until it is warm. The fire lighting phase can be prolonged
by using a lot of kindling and 1-2 firelighters. When a layer of embers has been formed, add 2–3 dry logs.
5.0 Maintaining and cleaning your wood burning stove
Gaskets
With time, the gaskets will wear, and, in order to avoid wild combustion, they must be replaced as required.
Glass
If the wood you burn is too moist, you will get soot stains on the glass pane. They can be easily removed
using a damp cloth that you dip in cold ash and rub on the sooty glass. Special cleaning agents are also
available to remove soot from glass.
Vue de la page 6
1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire